Category Archives: UK

2.5RS, AWD, Drivetrain, Ej20, forester, gc8, Impreza, JDM, Legacy, Subaru, Suspension, UK, USDM

Antilock Brake System For Early Subaru Part 2:

Antilock Brake System for Early Subarus:

ABS Service And Brake Bleeding Procedures:

Antilock Brake System for Early Subarus: The first Subaru rally car the Legacy RS relied upon the bousch/nippon ABS units to perform on the WRC circuit.

Always check the fluid level of the master cylinder and bleed the wheel cylinders following the procedure listed in the service manual. When the HCU has been removed and/or replaced, the fluid must be drained. Replace the cone screws with bleed screws and attach a hose to drain fluid to a container.

Antilock: ABS Service And Brake Bleeding Procedures: A early Subaru Nippon ABS unit ECU.

Use extreme care when performing this procedure to prevent damage to the internal components of the HCU. Do not apply AV signal for more than 5 seconds for each application. If no AV signal is received, it is not necessary to close bleed screw between brake pedal applications.

Antilock Brake System Notes and Cautions:

The ECU on early Subaru ABS systems can only display one trouble code–the lowest numbered code. Correct the fault indicated by the trouble code and recheck ECU for another code. Repeat the self-diagnostic procedure listed above, and the next highest code will be displayed. Refer to the appropriate model year service manual for the trouble codes and corrective actions. While the ABS ECU is in the fault mode, the ABS will go to fail-safe and remain passive under all braking conditions. The brake system will function as a conventional power-assisted system without ABS.

Pages: 1 2 3 4 5
2.5RS, AWD, Drivetrain, Ej20, EJ25, forester, gc8, Impreza, STi, Subaru, Transmission, UK, USDM

Maintenance:Subaru Periodic Maintenance Part 3:

Maintenance: Subaru Periodic Vehicle Maintenance Services:

Brake Fluid:

Many late model Subaru vehicles are equipped with ABS braking systems. The added complexity of these systems provides an additional incentive for following the recommended brake fluid replacement interval of 30 months or 30,000 miles. Brake fluid accumulates water and other contaminants over time. These contaminants can attack the internal parts of the brake system, compromising its performance and possibly causing brake failure.

Maintenance: Subaru Periodic Vehicle Maintenance Services: Make sure to replace brake fluid at least every 30 months of 30,000 miles. At least once a year if the Subaru sees heavy track use.

The brake master cylinder has a semi-transparent reservoir, making it possible to check the fluid level without removing the reservoir cover. This minimizes the exposure to outside air and limits the amount of moisture that can reach the brake fluid. The fluid level will drop as the brake shoes and pads wear, but the reservoir is large enough to compensate for these changes. If the fluid level is very low, it’s a sure sign the brake pads or shoes are nearly worn out, or there is a leak in the brake system.

Note: When the brake fluid level in the reservoir tank is lower than the specified limit, the brake fluid warning light in the combination meter will come on.

Subaru warns against mixing brake fluids from different manufacturers. Doing so may degrade the quality of the fluid. Only DOT 3 or 4 brake fluid should be used in any Subaru vehicle preferably Subaru brake fluid if you are not going to do a track day build. Consult the service manual for vehicle specific brake bleeding procedures.

Subaru OEM Brake Fluid:

Subaru SOA868V9220 Brake Fluid – 1 Pint

Pages: 1 2 3 4
AWD, Drivetrain, Ej20, EJ25, EJ257, forester, gc8, Impreza, Legacy, STi, Transmission, UK, USDM, WRX

Maintenance:Subaru Periodic Maintenance Part 2:

Maintenance: Subaru Periodic Vehicle Maintenance Services:

Maintenance: Subaru Periodic Vehicle Maintenance Services: Often the best value and best parts come from Subaru themselves and often aftermarket replacement parts will be of substandard quality.

Fuel Filter and Fuel Lines:

There’s no easy way to check the inside of a fuel filter for dirt or other contamination buildup. That’s why a 30 month or 30,000 mile replacement interval is prescribed. If the customer happens to buy a tank-load of bad gasoline before reaching this interval, it will be necessary to replace the fuel filter ahead of time. There’s no way to clean the filter—replacement is the only option. Remove the battery negative cable before you begin work on the fuel filter. Remember gasoline is a very flammable substance.

The fuel filter is just one small part of the fuel system. The fuel system includes many sections of steel and rubber fuel line that run the length of the vehicle several times. The fuel pump, fuel tank, and fuel pressure regulator are just a few of the other parts of the fuel system. While you’re replacing the fuel filter, don’t forget to check the condition of the rest of the fuel system.

Maintenance: Subaru Periodic Vehicle Maintenance Services: Pictured is a Subaru STi fuel system. Making sure your filter is in good condition and is replaced regularly will prevent problems from occurring.

If any of the rubber hoses (especially the ones that were opened up to replace the filter) look damaged or frayed, they must be replaced before they can cause any further damage. Weak fuel hose clamps should be replaced, and the new ones must be properly positioned and tightened to specification.


Subaru 42072PA010 Fuel Filter

Pages: 1 2 3 4
Ej20, ej20G, EJ25, EJ257, Impreza, STi, Subaru, Turbo, UK, USDM, WRX

Valve Cover Gasket replacement Subaru WRX:

Valve Cover Gasket replacement Subaru WRX:

This is a step by step guide on replacing the valve cover gasket on Subaru flat four engines. This guide will work for most Subaru turbo cars 02-07+ and most other naturally aspirated Subaru cars.

1.) Jack your car up and drain the oil. Remember to put the car on jack stands. You don’t want the car dropping on you.A lot of people do this job with the oil still in the pan, but its better to rather play it safe and drain the oil completely.

2.) Remove the front air scoop. It takes two 10mm bolts.

3.) Remove the nice Cold Air intake box.

4.) After removing all that, you should see this a total of 8 outer bolts and the 2 inner which holds the spark plug coils.

Valve cover gasket: In the center are the two coil packs that need to be removed.

5.) Unscrew them and label them. You don’t want the bolts going into the wrong place. It was a very hard to get any decent clearance so take your time.

Pages: 1 2
Drivetrain, Ej20, EJ25, EJ257, exhaust, STi, Subaru, Turbo, UK, USDM

Oil pan removal and install on Subaru STi/WRX:

Oil pan removal Subaru STi/WRX:

This is a step by step guide on removing and re-installing a oil pan on your Subaru Impreza STi or WRX. This guide is also useful for installing a STi spec oil pan onto your WRX. This guide also is helpful if you are removing your stock oil pickup tube that is known to crack on the STi. I suggest purchasing a Killer B Motorsport Pickup Tube along with a brand new STi oil pan. Both can be purchased from down below from Amazon.

Brand new STi oil pan:

Subaru 11109AA131 Oil Pan

Killer B Motorsport Pickup Tube:

Killer B Motorsport Subaru Oil Pan Pickup Tube for EJ25 WRX/STI

 

Oil Pan Removal Steps:

1) Remove the plastic under tray from your engine. This is secured using a few bolts and plastic push clips.

2) Remove the plastic under trays from either side of the car, the long ones.

Oil pan removal and install: Remove plastic to gain access to the bottom of the engine.

3) Remove the jacking plate. This is held on by 2 12mm bolts with nuts in the front, 2 12mm bolts in the rear and 4 14mm nuts on the sides.

4) Remove your subframe. This is secured by a few 19mm bolts, 2 12mm bolts in front and 4 14mm bolts. I highly recommend soaking these all in your PB blaster and waiting 5 minutes. Check out some of my other posts for instuctions.

5) Remove the front oxygen sensor. The correct way is to unplug the clip, unhook it from the metal mount and then pull the wire through the fender-well so that the wire isn’t being stretched and twisted as you unscrew it.

O2 sensor location in the exhaust manifold.
Pages: 1 2 3 4 5
AWD, Ej20, ej20G, Intake, Intercooler, JDM, Legacy, Rally, Subaru, TMIC, Tuning, Turbo, UK, wrc

Legacy: 1989-1994 Subaru Legacy (BC/BF) GT/RS

Prior to the Legacy RS turbo, Subaru had never enjoyed the experience of distributing a genuine performance car. Of course, there had been the 4WD turbo RX and Vortex, but neither could crack 10 seconds for the 0-100km/h sprint – although they were very reliable. The RS was the gun version of the first Legacy series released in 1988 and discontinued in 1994. The RS (Rally Sport) model was aimed squarely at world rallying, with many of its components and concepts carried over to the dominating Impreza WRX.

Legacy: The BC/BF is unique in having an Air – Water intercooler with a front mounted radiator for optimal cooling. The bonnet scoop only provides cooling to the turbo. While later model legacy’s have all used air to air intercoolers.

The center Viscous LSD on the MT models initially starts out with a 50/50 torque split, front and rear, and will up the ratio towards the end with more traction. The manufacturer doesn’t give a final figure, so the max split is either 65/35, or could even venture as high as 95/5, since the A/T model has a different system that is marketed at a 65/35 maximum split. A higher ratio would explain some of the handling characteristics at the limit. The rear differential is also a Viscous LSD model.

The BC/BF is unique in having an Air – Water intercooler with a front mounted radiator for optimal cooling. The bonnet scoop only provides cooling to the turbo. While later model legacy’s have all used air to air intercoolers.

Pages: 1 2 3
AWD, gc8, Prodrive, STi, Subaru, TMIC, Turbo, UK, wrc, WRX

Prodrive GC8 WRX Special Editions

22B “Type UK”

In late 1998, Subaru UK officially imported 16 22Bs (described below), and passed them on to Prodrive for modification. The UK cars differ from the privately imported 22Bs, not just in their 3 year factory warranty, but with revised gear ratios more suited to UK roads.

This was achieved by changing the final drive ratio from 3.9 to 4.44 to lengthen the gearing. Cosmetically, the car got the headlights from the ‘99 model, UK rear light clusters and driving lights (not fog lights!) were fitted where the normal 22B has blanking plates. From the back, you can tell you’re looking at one of the rarest cars in the world by the “Type UK” and “Prodrive” stickers. The price was £39,950, and demand for the cars was overwhelming.

The rear of a Prodrive 22B Type UK.

Interestingly, Subaru UK were not able to put their 16 cars through the Single Vehicle Approval scheme because the maximum of 50 privately imported 22Bs had already been registered in 1998. Consequently the Type UKs were registered in 1999. The cars do not meet European Type Approval regulations for noise and emissions.

Pages: 1 2 3 4
AWD, gc8, Rally, Turbo, UK, WRX

McRae UK WRX 1st Gen special editions

McRae UK WRX 1st Gen special editions

Series McRae

In June 1995, to celebrate their winning of both the manufacturers and drivers World Rally Championship titles, Subaru in the UK released a limited edition run of two hundred cars (numbered 1 to 201 – no number 13!) prepared by Prodrive going by the name of the Series McRae. The main improvements over the standard model are:

  • Special mica blue paintwork
  • 6.5 x 16 inch eight spoke gold Speedline Safari alloy wheels
  • Pirelli P Zero 205/50 ZR 16 low profile tyres
  • Recaro sports front seats with open headrests and Series McRae motifs
  • All seats (front and back) and door panelling retrimmed in Le Mans/Avus material
  • Factory fitted electric tilt and slide sunroof
  • Interior numbered Series McRae plaque
  • Side and rear Series McRae decals

On the road price was £22,999

A official Subaru WRX poster for the Series McRae.

Next page will be the Catalunya edition!

Pages: 1 2 3