Tag Archives: Jdm

AWD, forester, gc8, Impreza, STi, Subaru, Suspension, UK, USDM, WRX

Maintenance: Subaru Periodic Maintenance Part 4:

Maintenance: Subaru Periodic Maintenance Part 4:

Steering and Suspension:

Steering and suspension parts are a lot like the brake system components. Their proper operation is vitally important to the safety of the driver and his passengers, but it is very difficult to determine how long it will be before any of these components will require attention. That’s why an inspection of all steering and suspension components is required at 15 month/15,000 mile intervals. Changes to these systems may be too gradual for the driver to even notice, leaving it to you to ferret out and correct any wear or damage that has taken place.

Maintenance:Subaru Periodic Maintenance Part 4: Regular checks of the steering and suspension is important.

We won’t cover all of the steering and suspension checks here. There’s too much variation between different Subaru models to do an adequate job. What you’re looking for is anything that reduces the original precision of the steering and suspension systems. Perhaps the steering has a little too much play in it or the shocks and struts don’t handle the bumps in the road as well as they did when new. Specific tests for the Subaru model you’re working on can be found in the service manual.

Check the power steering system for dampness or other signs of fluid leakage. The power steering pump reservoir is a good place to start. If the reservoir is low, the fluid has probably leaked out, as it has no place else to go. Approved fluids for the power steering system include Dexron II, IIE or III.


GENUINE OEM SUBARU ATF-HP P/S FLUID QUART BOTTLE

Pages: 1 2 3 4
EJ257, Intercooler, JDM, STi, Subaru, TMIC, Turbo, USDM

JDM Automatic Intercooler STi Switch Install:

JDM Automatic Intercooler STi Switch Install:

Here is the step by step guide to installing the JDM Automatic Intercooler STi switch. For those of you wondering the advantage of upgrading to the JDM automatic intercooler switch is that it essentially works as a on/off switch for the STi intercooler sprayer. So there is no more constant pushing of the sprayer button. Push the button once to turn it on, and again to turn it off. However, it will empty out your intercooler sprayer tank very quickly if you keep it on.

Here is the switch we are going to be installed:

JDM Automatic Intercooler Switch: The JDM intercooler switch that you will be installing.

1.) Pop out the fuse box panel. The fuse box panel is located underneath and to the left of the steering wheel.

2.) Use your fingers to depress the tab on the button of the button to pop it out.

JDM Automatic Intercooler Switch: The USDM stock STi switch that you will be removing.

3.) Pull the switch out of the dash.

4.) Depress the tab on the back of the plug to remove the switch.

JDM Automatic Intercooler Switch: USDM STi intercooler switch removed. Get ready to install the JDM switch now.
Pages: 1 2
JDM, STi, Subaru, USDM, WRX

Lips: V-Limited Lip Subaru WRX STi Install guide:

V-Limited Lip Subaru WRX/STi Install guide:

Today we have for you an installation guide for the STi V-Limited Lip. It is being installed on a 2006 STi, but the procedure will be very similar for a V-Limited Lip installation on any other compatible Subarus.

Give your car that extra bit of JDM styling you’re looking for while adding performance at the same time! Constructed of 100% ABS plastic (the same material as your factory bumper), the V-Limited Lip is securely attached underneath the front bumper by a series of small bolts.
This is one of very few front lips available on the market that actually has a performance aspect too it. The design of the lip allows for an increase in front down force, improving your car’s handling at higher speeds. Don’t be fooled by imitations lips that are made of a hybrid material or fiberglass. These “replica” lips are flimsy and very prone to breakage. Treat yourself to the real thing and order your V-Limited Lip today! Don’t forget to protect your new V-Limited Lip with a rubber lip protector.

1. For this install you will need to get the front end of the car in the air. It doesn’t need to be that high, just enough to get under the front of the car. A jack stand under each of the two front lift points should do, ramps will also work if you have them.

2. First, you will need to mount the lip under the bumper so that it will stay steady while you drill the holes. Remove the plastic clips circled in the picture (three more on other end of bumper). Attach the lip to the bumper, but do not reattach the plastic cover’s flaps to the bumper as they were before.

Pages: 1 2
Ej20, ej20G, EJ257, JDM, TMIC, Tuning, Turbo, USDM, WRX

Turbo: STi/WRX VF Series Turbocharger breakdown:

Turbo: STi/WRX VF Series Turbocharger breakdown:

IHI VF Series
The numbering on both the VF turbos are for reference purposes and not necessarily indicative of its ‘performance’. On GC8/GF8 WRX STi, the VF turbos have gone ‘smaller’ from VF22 to 23, 24, 28, 29 while the release of the New Age STi GDB saw the introduction of a new breed of VF turbos with a bigger compressor wheel namely, VF30, VF34, VF35 for example. The previous VF turbos (VF22,23,24,28,29) have been ball bearing cored while the later ones (VF30, VF35) are Divided Thrust Bearing type core, with the VF34 being a Ball Bearing.

IHI VF22
(455cfm at 18.0psi, 250-325whp, Bolt-On)
The VF22 has the largest potential for peak horsepower. In other words, in the IHI model range, the VF 22 supports the highest boost levels. With its significantly increased turbine housing, the VF22 turbo is capable of producing upwards of 310 whp* on an EJ20. The downside of this turbo is the older center cartridge design and larger compressor housing, which makes for slower spool up but more top-end than the other VF series turbos.

This turbo is the best choice for those who are looking for loads of top end power. The top end power however, does not come without a cost. The VF22 spools significantly slower than the rest of the IHI models due to the larger P20 exhaust housing and is much less suited for daily driving than some of the other models. Although the largest VF series turbo, the VF22 is not quite optimal for stroked engines or those who wish to run more than 20PSI of boost.

The VF22’s compressor is rated at 35 lbs/minute. The VF22 was designed with the EJ20 in mind but because it has the biggest turbine in the IHI family it can be use on the EJ25 with a slight increase in performance. The VF22 is good for around a realistic 300 to 315 WHP on a 2.0L. The IHI VF-22 turbo is the largest of the VF-series turbos.

VF22: The IHI VF-22 turbo is the largest of the VF-series turbos.

IHI VF34
(440cfm at 18psi, 250-325whp, Bolt-On)
The VF34 is nearly identical to the VF30, with the same exhaust housing and compressor. However the VF34 goes back to the ball bearing design, and in doing so achieves full boost approximately 500RPM sooner than the comparable VF30. The VF34 is the most recent IHI design and as such costs slightly more than its counterpart.

Top end performance and maximum output are identical to the 30. The VF34’s compressor is rated at 35 lbs/minute but the turbo suffers from the same turbine restrictions found with the VF30. The VF34 was designed with the EJ20 in mind and will not have the same performance on an EJ25. The VF34 is good for around a realistic 290 to 305 WHP on a 2.0L.

VF34: The VF34 was designed with the EJ20 in mind and will not have the same performance on an EJ25. The VF34 is good for around a realistic 290 to 305 WHP on a 2.0L.
Pages: 1 2 3 4
EJ257, Intercooler, JDM, STi, Subaru, TMIC, Turbo, WRX

TMIC basics on a Subaru WRX/STi

TMIC basics on a Subaru WRX/STi:

The primary purpose of a top mount intercooler is to reduce post turbo air temperature prior to entering the combustion chamber via the throttle body.

HP gain is around 15HP. This figure can vary as many TMICs replace the restrictive OEM piping and results can be further enhanced with post installation tuning. This is one modification that is extremely difficult to put a traditional HP figure on as results truly vary from car to car based on tuning and turbo output in terms of CFM.

How much HP can my stock TMIC hold? 300WHP on the WRX and 400WHP on the STi are attainable. That does not mean those power levels are 100% efficient, but that those power levels are attainable with their OEM TMICs. As discussed below though, TMICs are not meant to be HP rated, but rather CFM related, but this is an FAQ so the HP figures are given as a good “bad” answer.

TMIC basics on a Subaru WRX/STi: 04-07 STi OEM TMIC

Which manufacturer is best? This topic is highly debated. There have been no reported consistent “bad” TMICs on the market. Obviously, there may have been bad TMICs sold, but not enough to report as “bad” overall.

I have a 2008/2009 model, any differences? Yes. Your engine bay has an entirely new layout vs. the 2002-2007 models.

TMIC basics on a Subaru WRX/STi: A 2008 STi stock TMIC
Pages: 1 2 3 4 5
AWD, BBS, DCCD, Impreza, JDM, Recaro, STi, Subaru

Impreza Second Gen WRX JDM special models

Second Generation Impreza WRX JDM special variants:

Subaru Impreza S202: This car was an S-series Impreza based on the Spec C. All of the suspension and powertrain parts included STi parts from the STi part catalog.

S202
This car was an S-series Impreza based on the Spec C. All of the suspension and powertrain parts included STi parts from the STi part catalog. The interior included special edition yellow seats with red STi logo stitching. A smaller, lightweight AC compressor was fitted to save weight. The brake rotors were gas slotted. The wheels were STi labeled Rays Volk alloys.

Subaru Impreza S203

S203
This limited edition Subaru was an S-series Impreza based on the WRX STi. Again it is basically a car with all the STi parts available. It was sold with custom made 18-inch (460 mm) BBS alloys with Pirellis.

Subaru Impreza S204 render
Pages: 1 2 3