Category Archives: EJ25

AWD, Ej20, EJ25, EJ257, Intake, Intercooler, STi, Subaru, Turbo, USDM, WRX

FMIC (Front Mount Intercooler) STi/WRX FAQ

FMIC: The primary purpose of a FMIC (front mount intercooler) is to reduce post turbo air temperature prior to entering the combustion chamber via the throttle body.

FMIC install in a Subaru WRX STi.

HP gain is around 15HP. This figure can vary as results can be further enhanced with post installation tuning. This is one modification that is extremely difficult to put a traditional HP figure on as results truly vary from car to car based on tuning and turbo output in terms of CFM.

Which manufacturer is best? This topic is highly debated. There have been no reported consistent “bad” FMICs on the market. Obviously, there may have been bad FMICs sold, but not enough to report as “bad” overall.

Which FMIC construction method is best? FMICs have two main construction methods:
1. tube and fin
2. bar and plate
There is much debate as to which construction method is best. There are many pros and cons with each design type, but no real hard data. Bar and plate designs are consistently reported as more damage resistant which gives them the edge with regard to appearance longevity. In the end, you are best advised to chose a FMIC based on other qualities rather than concentrate on construction design.

Pages: 1 2 3 4 5 6
EJ25, EJ257, STi, Subaru, Tuning, Turbo, USDM, WRX

Pulley Subaru WRX/STi Rundown

The primary purpose of an aftermarket pulley is to reduce the size and/or mass of the stock unit. They serve two purposes: to reduce horsepower loss and increase throttle response. Notice the use of “reduce horsepower loss”. Pulleys DO NOT add horsepower, rather they free up horsepower due to the reduction of rotational mass.


Grimmspeed Lightweight Crank Pulley Black – Subaru All EJ Engines

A lightweight aftermarket perrin pulley.

HP gain is 5-10HP. These HP figures are a range as there have been very few before/after dyno runs with lightened or under driven pulleys.

What is a lightened pulley? Generally, it is an exact copy of the OEM pulley only CNC machined out of aircraft grade aluminum and powder coated for corrosion protection and aesthetic appeal.

What is an under driven pulley? This is a pulley that mimics the function of the OEM unit, but is smaller in diameter. This will reduce the duty cycle of the pulley and proportionally the parasitic drag on the engine.

Are under driven pulleys bad? It depends on the amount they are under driven. Some under driven pulleys can lead to reduced A/C output, lighting problems, stereo problems, and other voltage issues. Some are lightly under driven and some more so.

Isn’t replacing the stock harmonic damper (pulley) bad? Subarus do not come with a harmonic damper or balancer like some other vehicles do. For other manufacturers’ vehicles, this is a legitimate concern. Proof:

“Thank you for your patience as I checked with our Technical Services Department regarding your message below. They advised that the crank pulley is a pulley and nothing else. It is not used as a harmonic damper/balancer.

Thanks for the opportunity to be of assistance. If you need any future assistance, please feel free to contact us again.”

Best wishes,

John J. Mergen
Customer Service Department
Subaru of America, Inc.

Pages: 1 2 3
Ej20, EJ25, EJ257, Intercooler, STi, Subaru, TMIC, Turbo, USDM, WRX

Header Aftermarket Turbo Subaru FAQ

Header Aftermarket Turbo Subaru FAQ

The primary purpose of an aftermarket header on a turbocharged Subaru is to remove or replace the stock exhaust manifold with a better flowing unit.

An Agency Power Stainless Steel Header for a EJ257.

HP gain is 15HP and 20TQ. This figure is highly debated as different manufacturers use different dynos with different cars with different levels of mods. It also varies because some headers incorporate an uppipe into their design. This makes it nearly impossible to compare the gains of a header without an uppipe vs. a header with an uppipe.

Which manufacturer is best? This topic is highly debated. There have been no reported consistent “bad” headers on the market. Obviously, there may have been bad pipes sold, but not enough to report as “bad” overall.

Where can I find headers?

Subaru WRX STI Header Prosport Unequal Length Stainless Steel Header

Perrin Subaru STi /WRX Header Equal Length Big Tube

AP WRX/ STI Stainless Steel Unequal Length Header w/o Uppipe

Invidia HS05SW1HDR Racing Header for Subaru WRX STI/Legacy GT

Agency Power (AP-GDA-175) Unequal Length Header, Stainless Steel

Perrin PSP-EXT-050 04-08 STi /LGT/FXT/06-08 WRX (06+ WRX requires modification to oil cooler) Header (02-05 WRX Requires STi Oil Pan)

TOMEI 193082 Headers

What differences are there with headers? The main difference is exhaust piping length. Headers are made to be unequal length or equal length. Unequal means the piping on the driver’s side of the engine will be longer than the passenger’s side. Equal means the piping length is equidistant from the engine outlet to the header outlet for all piping.

Pages: 1 2 3
anti-lag, EJ25, Facebook, Impreza, Turbo, wrc

World Rally Championship BOV/Anti-lag system

Sometimes if you spent more than five minutes posting facebook and instead searched on google you might understand the World Rally Champion anti-lag system that’s used on Subaru’s rally cars.

 It gets to a point were none of these people should own a turbocharged Subaru. True anti-lag systems are expensive and require extensive tuning and kills turbos which translates into a lot of money which none of these people have.