Category Archives: Suspension

AWD, STi, Subaru, Suspension, USDM, WRX

Rear Differential Bushings install Subaru WRX/STi

Rear Differential Bushings install Subaru WRX/STi:

This rear differential bushing install process took all of about an hour and a half. What you will need is:

Rear Diff Bushings:

Whiteline KDT905 Rear Differential Support Bushing

Whiteline W92835 Rear Differential Mount Bushing

 

I used a 3/8″ drive set
17mm Medium Depth socket
17mm Open ended Wrench
Swivel For socket (optional) i didnt need this
Torque Wrench (specs for all of these nuts and bolts are 51.6ft lbs)
Couple of screwdrivers or Pry bars ( i prefer Prybars)
C-clamp
Hammer (optional)
Transmission lift (to hold up the rear diff when the bolts are out, you will also need this to lower the diff down to get the outside bolts over the rear axles)

1.)
Get the vehicle in the air some how, this is easiest if you have access to a garage with a lift. Which i did that only costs about $2.00 an hour. Once its on the lift go ahead and locate the area with the bolts and make sure you unplug the rear diff sensor and ground.

2.)
Unbolt the two outer nuts, you will notice that the bolt goes in from the axle side. Make sure to put them back the same way.

3.)

Now that the outside bolts are out, what you need to do it take the nuts that you have taken off from the outside and thread them over the two inner bolts that hold on the rear diff. What this does is make it able for you to take out the bolt that is directly screwed into the diff. Make sure you thread it all the way, and once they are tight, using your open ended wrench start to back off the inner nut, and it might turn a little bit without the whole thing moving but thats ok, a few turns and the whole thing will break free. ( be carefull for the rear diff sensor)

4.)
Once you get the two studs holding the rear differential in place you should be able to let down your transmission stand a little bit to move the axles out of the way and pull the studs out of the outside two bushings.

Pages: 1 2
AWD, Stance, Subaru, Suspension, WRX

Spring Installation guide for Subaru WRX STi:

Spring Installation guide for Subaru WRX STi:

 

1.) Remove the rear seat.

Tools: 12mm socket. Socket extension helps.

There are two brackets at the front of the rear seat. Remove the bolts holding them in and pull out the lower seat cushion. There are three brackets holding the seat back in. Once the bolts are out you can lift the cushion off. There are brackets at the top that support the seat; make sure those clip in properly when you put it back in. Also pay attention to how the cushion fits through the seat belt.

2.) It is easiest to bust loose the 17mm strut top nuts while the car is on the ground. So that’s what we are doing here…

Once the seat is out you can get to the rear strut dust covers. You’ll want a couple of tools to get to these nuts since the access is pretty tight. A 12mm open gear wrench (pictured) is nice. Also, standard 12mm sockets in various depths will be helpful. Unless you have air tools that can fit on these, there is a lot of wrenching involved since you can only get a few degrees per turn on some of them. Strut cover removed. Note the “out” inscription, and make sure it faces “out” when you put it back on. Top of the strut showing the nut that needs to be loosened. You should be able to get on there with a 17mm deep socket and loosen it a few turns. Just bust it loose, do not remove it at this point!

This next part isn’t critical now, but you will need the info later.

In order to make sure the strut isn’t spinning in the shaft, you need to insert a 6mm hex/allen wrench
into the strut top, and hold that still while you turn the 17mm nut. This is the contraption I use.

Now to the front.

Remove the little rubber dust covers in the center of the top mounts. Again, bust the top nut loose. On the front passenger side there may be a bracket that holds an alarm chirper. It doesn’t really matter if you take the 12mm nuts off now or later, I am just including it at this point in the process. If you do loosen them now, again, make sure to keep them on at least a little bit so the struts don’t fall off later.

Pages: 1 2 3 4 5 6