Category Archives: Stance

Impreza, Stance, STi, Subaru, WRX

Hood damper Installation for Subaru WRX/STi

Hood damper Installation for Subaru WRX/STi:

This is a Tein hood damper installation guide for your Subaru Impreza WRX/STi.

Tein BHD01-S28 Hood Damper for Subaru Impreza

Tools Required: 10mm Socket
12mm Socket
Razor

1. Inspect contents of the kit!

Tein hood dampers: Note the Red bottle is the thread locker, clear bottle is grease!

Note the Red bottle is the thread locker, clear bottle is grease!

2. Assemble the dampers by attaching the aluminum extensions to the long ball joint and damper body
Apply thread locker to all threads.
The small ball joint goes on the other end!

3. Next, remove the center fender bolt using a 10mm socket and ratchet, install the joint ball post and washer into this bolt hole, use the tread locker. Torque to 7.5ftlbs.

4. Use a razor to make a clean cut to the factory rubber molding from the fender to the beginning of the engine bay.

5. Take an assembled Tein Hood Damper and remove the locking pin from the Ball Joint (female end), using a little grease cover the male end and place female end over the male end, re-insert locking pin.

Note, the left hand side can be rotated as pictured above to insert the locking pin and then rotated back to the hood.

Pages: 1 2
AWD, Stance, Subaru, Suspension, WRX

Spring Installation guide for Subaru WRX STi:

Spring Installation guide for Subaru WRX STi:

 

1.) Remove the rear seat.

Tools: 12mm socket. Socket extension helps.

There are two brackets at the front of the rear seat. Remove the bolts holding them in and pull out the lower seat cushion. There are three brackets holding the seat back in. Once the bolts are out you can lift the cushion off. There are brackets at the top that support the seat; make sure those clip in properly when you put it back in. Also pay attention to how the cushion fits through the seat belt.

2.) It is easiest to bust loose the 17mm strut top nuts while the car is on the ground. So that’s what we are doing here…

Once the seat is out you can get to the rear strut dust covers. You’ll want a couple of tools to get to these nuts since the access is pretty tight. A 12mm open gear wrench (pictured) is nice. Also, standard 12mm sockets in various depths will be helpful. Unless you have air tools that can fit on these, there is a lot of wrenching involved since you can only get a few degrees per turn on some of them. Strut cover removed. Note the “out” inscription, and make sure it faces “out” when you put it back on. Top of the strut showing the nut that needs to be loosened. You should be able to get on there with a 17mm deep socket and loosen it a few turns. Just bust it loose, do not remove it at this point!

This next part isn’t critical now, but you will need the info later.

In order to make sure the strut isn’t spinning in the shaft, you need to insert a 6mm hex/allen wrench
into the strut top, and hold that still while you turn the 17mm nut. This is the contraption I use.

Now to the front.

Remove the little rubber dust covers in the center of the top mounts. Again, bust the top nut loose. On the front passenger side there may be a bracket that holds an alarm chirper. It doesn’t really matter if you take the 12mm nuts off now or later, I am just including it at this point in the process. If you do loosen them now, again, make sure to keep them on at least a little bit so the struts don’t fall off later.

Pages: 1 2 3 4 5 6
Facebook, Impreza, Ricer, Stance, Subaru, WRX

What’s that noise? My Subaru is so low that the axle is hitting the pinch welds?

So I have nothing against a nicely stanced Subaru put together with quality parts. However, when your Subaru is so low that your axles are grinding into the body/frame of the Subaru we might have a problem.

I mean what’s the worst that can happen? Maybe the axle grinds in half and snaps while driving down the road and you have an accident. Hopefully yourself or no one else is injured